Re: [情報] M.Benz提前發表全新1.6升V6渦輪增壓引擎

看板FORMULA1 (F1 賽車)作者 (車)時間13年前 (2013/04/08 23:28), 編輯推噓6(6011)
留言17則, 5人參與, 最新討論串3/4 (看更多)
※ 引述《ASKA (壞羊男有點溫柔)》之銘言: : 我也覺得怪怪的。所以去查了規則。 : http://ppt.cc/FSWs : 2014 F1 Technical Regulations - Fia : 第五章是關於引擎的。 : 5.3 Power unit dimensions : : 5.3.1 Cylinder bore diameter must be 80mm (+/- 0.1mm). : 5.3.2 The crankshaft centre line must lie on the car centre line and : 90mm (+/-0.5mm) above the reference plane. The power unit may only transmit : torque to the gearbox by means of a single output shaft that must be : co-axial with the crankshaft. The output shaft must rotate clockwise when : viewed from the front of the car. : 5.3.3 Valve stem diameter must not be less than 5mm. : 5.3.4 The power unit must be installed in the union of the volumes that exist : between two vertical planes normal to the car centre line separated by 700mm vertical plane是指垂直地表的平面? 兩個垂直地表的平面又要跟中心線垂直 所以平面的法線方向水平指向車頭 兩平面要分隔700mm 所以power unit要裝在沿車長(ㄔㄤˊ)方向的700mm之內? : and in a box 150mm long, 250mm wide and 800mm high which lies symmetrically 假設long也是沿車長(ㄔㄤˊ)方向計算 V型6缸 曲軸又要在中心線上(見5.3.2) 所以150mm要塞三個汽缸? 缸徑又80mm(見5.3.1)就爆炸了啊 orz : about the car centre line immediately ahead of the front vertical plane. 然後就看不懂了 orz : ... : 我覺得應該是指單一排汽缸的尺寸吧?... : 有對這熟的鄉民可以解說一下嗎? --    ◤██▂▅ ◢_▁▂▃▅▇   ◤█◢   ◢_▁▂▃▅▇  ◤███◢ ◢  ▁▃▅▇ ◤█◢     ◢▁▃▅▇ -- ※ 發信站: 批踢踢實業坊(ptt.cc) ◆ From: 111.243.22.187

04/08 23:33, , 1F
長150mm=15cm, 寬250mm=25cm, 高800mm=80cm
04/08 23:33, 1F

04/08 23:35, , 2F
缸徑80mm=8公分 三個汽缸至少24公分(綜向排列)
04/08 23:35, 2F

04/08 23:36, , 3F
我沒看到哪裡有寫缸徑80mm阿??
04/08 23:36, 3F

04/08 23:37, , 4F
5.3.1 Cylinder bore diameter must be 80mm
04/08 23:37, 4F

04/08 23:38, , 5F
原來在那麼高的地方QQ
04/08 23:38, 5F
※ 編輯: dn890221 來自: 111.243.22.187 (04/08 23:41)

04/09 01:38, , 6F
是在說引擎必須安裝在兩個間距700mm的平面中間
04/09 01:38, 6F

04/09 01:38, , 7F
然後在前平面的前方還有個額外的150*250*800的方形空間
04/09 01:38, 7F

04/09 01:39, , 8F
....嗎?
04/09 01:39, 8F
我忽然看懂了?union的意思是那兩個空間的聯集

04/09 01:42, , 9F
至於那個方型空間應該就是拿來裝ERS的吧
04/09 01:42, 9F

04/09 01:45, , 10F
http://ppt.cc/zoBk 這邊有詳細資訊
04/09 01:45, 10F
│←車身中心線 ──────── ┐ │ 車 對於這個空間 │ 頭 這幾條規則 700mm 方 沒有直接規範 │ 向 │ ↓ ──┬──┬── ┤ │H=80│ 150mm └──┘ ──┘ └25cm┘ │←車身中心線 ※ 編輯: dn890221 來自: 111.243.22.187 (04/09 01:59)

04/09 02:01, , 11F
個人覺得上圖應該700mm是"寬" 應該不是"長"
04/09 02:01, 11F

04/09 02:03, , 12F
應該是原PO的圖那樣沒錯了
04/09 02:03, 12F

04/09 02:06, , 13F
vertical planes normal to the car centre line
04/09 02:06, 13F

04/09 02:06, , 14F
separated by 700mm
04/09 02:06, 14F

04/09 02:07, , 15F
個人的解讀是平面要跟車身中心垂直 且相距700mm
04/09 02:07, 15F

08/08 09:58, , 16F
缸徑80mm=8公分 https://noxiv.com
08/08 09:58, 16F

09/10 23:31, , 17F
5.3.1 Cylin https://daxiv.com
09/10 23:31, 17F
文章代碼(AID): #1HOk8qFi (FORMULA1)
文章代碼(AID): #1HOk8qFi (FORMULA1)